lite-on dcc release lite-on technology corp. / optoelectronics no.90,chien 1 road, chung ho, new taipei city 23585, taiwan, r.o.c. tel: 886-2-2222-6181 fax: 886-2-2221-1948 / 886-2-2221-0660 http://www.liteon.com/opto through hole lamp product data sheetLTL17KCBH5D spec no.: ds20-2009-0181effective date: 03/24/2015revision: c bns-od-fc001/a4 bns-od-fc001/a4 bns-od-fc001/a4 bns-od-fc001/a4
1 / 9 part no. : LTL17KCBH5D bns - od - fc002/a4 through hole lamp ltl 17kcbh5d through hole lamp ltl 1 7 kcbh5d rev description by date above data for pd and customer tracking only - nppr receive and upload on opnc ormjitm 10/13/2009 a update paper correction in p. 2 from 50c to 30 c in max. rating. ormjitm 03/15/2011 b up date ds leo kc chen 05/22/2012 c update new format and revise packing spec pantakarn k 03/11/2015
2 / 9 part no. : LTL17KCBH5D bns - od - fc002/a4 through hole lamp ltl 17kcbh5d 1. description through - hole leds are offered in a variety of packages such as 3mm, 4mm, 5mm, rectangular, and cy linder which are suitable for all applicatio ns requiring status indication. several intensity and viewing angle choices are available in each color for design flexibility. 1 . 1. features ? low power consumption & high efficiency ? lead free & rohs compliant ? p opular t - 1 diameter ? ingan blue 470 nm with blue diffused lens 1.2 . applications ? communication ? computer ? consumer ? home appliance ? industrial 2 . outline dimensions notes : 1. all dimensions are in millimeters (inches). 2. tolerance is 0.25mm (.010") unless ot herwise noted. 3. protruded resin under flange is 1.0mm (.04") max. 4. lead spacing is measured where the leads emerge from the package. 5. specifications are subject to change without notice. see note 3 2 . 5 4 ( . 1 ) nom. min. 2 5 . 0 ( . 9 8 4 ) cathode 1 . 0 ( . 0 4 ) min. 0 . 5 0 . 0 5 ( . 0 9 6 . 0 2 ) 3 . 1 3 . 8 ( . 1 2 2 ) ( . 1 5 ) 1 . 7 5 ( . 0 6 9 ) 5 . 4 ( . 2 1 2 ) 2 . 0 ( . 0 8 )
3 / 9 part no. : LTL17KCBH5D bns - od - fc002/a4 through hole lamp ltl 17kcbh5d 3. absolute maximum ratings at ta=25 parameter maximum rating unit po wer dissipation 108 mw peak forward current (duty cycle Q 1/10, pulse width Q 10ms) 100 ma dc forward current 30 ma derating linear from 3 0 0. 5 ma/ operating temperature range - 3 0 c to + 80 c storage temperature range - 40 c to + 100 c lead soldering te mperature [2.0mm (.079") from body] 260c for 5 seconds max. 4. electrical / optical characteristics at ta=25 parameter symbol min. typ. max. unit test condition luminous intensity iv 180 240 880 mcd if = 20ma note 1,5 viewing angle 21/2 50 deg note 2 (fig.6) peak emission wavelength p 468 nm measurement @peak (fig.1) dominant wavelength d 46 0 470 475 nm note 4 spectral line half - width ? 2 2 nm forward voltage vf 2. 7 3. 2 3.6 v if = 20ma reverse current ir 100 a vr = 5v (note 6) note: 1. luminous intensity is measured with a light sensor and filter combination that approximates the cie eye - response curve. 2. 1/2 is the off - axis angle at which the luminous intensity is half the axial luminous intensity. 3. iv classifica tion code is marked on each packing bag. 4. the dominant wavelength, d is derived from the cie chromaticity diagram and represents the single wavelength which define s the color of the device. 5. iv guarantee must be included with 15% testing tolerance. 6. reverse voltage (vr) condition is applied for ir test only. the device is not designed for reverse operation.
4 / 9 part no. : LTL17KCBH5D bns - od - fc002/a4 through hole lamp ltl 17kcbh5d 5. typical electrical / optical characteristics curves (25 ambient temperature unless otherwise noted)
5 / 9 part no. : LTL17KCBH5D bns - od - fc002/a4 through hole lamp ltl 17kcbh5d 6. packing specification 500 pcs per packing bag 1 0 packing bags per inner carton t otal 5 ,000 pcs per inner carton 8 inner cartons per outer carton t otal 40 ,000 pcs per outer carton in every shipping lot, only the last pack will be non - full packing
6 / 9 part no. : LTL17KCBH5D bns - od - fc002/a4 through hole lamp ltl 17kcbh5d 7. bin table specifica tion luminous intensity unit : mcd @ 20 ma bin code min. max. hj 180 310 kl 310 520 mn 520 880 note: tolerance of each bin limit is 15% dominant wavelength unit : nm @ 20 ma bin code min max b07 460.0 465.0 b08 465.0 470.0 b09 470.0 475.0
7 / 9 part no. : LTL17KCBH5D bns - od - fc002/a4 through hole lamp ltl 17kcbh5d 8 . cautions 8 . 1. application this led lamp is good for application of indoor and outdoor sign, also ordinary electronic equipment. 8 . 2. storage the storage ambient for the leds should not exceed 30c temperature or 70% relative humidity. it is recommende d that leds out of their original packaging are used within three months. for extended storage out of their original packaging, it is recommended that the leds be stored in a sealed container with appropriate desiccant or in desiccators with nitrogen am bient. 8 . 3. cleaning use alcohol - based cleaning solvents such as isopropyl alcohol to clean the leds if necessary. 8 . 4. lead forming & assembly during lead forming, the leads should be bent at a point at least 3mm from the base of led lens. do not use the base of the lead frame as a fulcrum during forming. lead forming must be done before soldering, at normal temperature. during assembly on pcb, use minimum clinch force possible to avoid excessive mechanical stress. 8 . 5. soldering when soldering, leav e a minimum of 3mm clearance from the base of the lens to t he soldering point. dipping the lens into the solder must be avoided. do not apply any external stress to the lead frame during sol dering while the led is at high temperature. r e commended soldering conditions : soldering iron wave soldering temperature soldering time position 350c max. 3 seconds max. (one time only) no closer than 2 mm from the base of the epoxy bulb pre - heat pre - heat time solder wave soldering time dip ping position 100c max. 60 seconds max. 260c max. 5 seconds max. no lower than 2 mm from the base of the epoxy bulb note: excessive soldering temperature and/or time might result in deformation of the led lens or catastrophic failure of the led. ir reflow is not suitable process for through hole type led lamp product. 8 . 6. drive method an led is a current - operated device. in order to ensure intensity uniformity on multiple leds connected in parallel in an application, it is recommended that a cur rent limiting resistor be incorporated in the drive circuit, in series with each led as shown in circuit a below. circuit model ( a ) circuit model ( b ) (a) recommended circuit (b) the brightness of each led might appear different due to the differences in the i - v characteristics of those leds. led led
8 / 9 part no. : LTL17KCBH5D bns - od - fc002/a4 through hole lamp ltl 17kcbh5d 8 .7. esd (electrostatic discharge) static electricity or power surge will damage the led. suggestions to prevent es d damage: ? use a conductive wrist band or anti - electrostatic glove when handling these leds ? all devices, equipment, and machinery must be properly grounded ? work tables, storage racks, etc. should be properly grounded ? use ion blower to neutralize the static charge which might have built up on surface of the leds plastic lens as a result of friction between leds during storage and handing suggested checking list : training and certification 8 .7. 1 .1 . everyone working in a static - safe area is esd - certified? 8 .7.1. 2. training records kept and re - certification dates monitored? static - safe workstation & work areas 8 .7.2.1 . static - safe workstation or work - areas have esd signs? 8 .7. 2. 2. all surfaces and objects at all static - safe workstation and with in 1 ft measure less than 100v? 8 .7.2. 3. all ionizer activated, positioned towards the units? 8 .7.2. 4. each work surface mats grounding is good? personnel grounding 8 .7.3.1 . every person (including visitors) handling esd sensitive (esds) items wear wrist strap, heel strap or conductive shoes with conductive flooring? 8 .7.3.1 . if conductive footwear used, conductive flooring also present where operator stand or walk? 8 .7.3.2 . garments, hairs or anything closer than 1 ft to esd items measur e less than 100v*? 8 .7.3.3 . every wrist strap or heel strap/conductive shoes checked daily and result recorded for all dls? 8 .7.3.4 . all wrist strap or heel strap checkers calibration up to date? note: *50v for blue led. device handli ng 8 .7.4. 1. every esds items identified by eia - 471 labels on item or packaging? 8 .7.4. 2. all esds items completely inside properly closed static - shielding containers when not at static - safe workstation? 8 .7.4. 3. no static charge generators ( e.g. plastics) inside shielding containers with esds items? 8 .7.4. 4. all flexible conductive and dissipative package materials inspected before reuse or recycle? others 8 .7.5. 1. audit result reported to entity esd control coordinator? 8 .7.5. 2 . corrective action from previous audits completed? 8 .7.5. 3. are audit records complete and on file?
9 / 9 part no. : LTL17KCBH5D bns - od - fc002/a4 through hole lamp ltl 17kcbh5d 9 . reliability test classification test item test condition sample size reference standard endurance test operation life ta = under room temperat ure if = per datasheet maximum drive current test time= 1000hrs 22 pcs (cl=90%; ltpd= 10 %) mil - std - 750d:1026 (1995) mil - std - 883g:1005 (2006) high temperature high humidity storage ta = 60 c rh = 90 % test time= 24 0hrs 22 pcs (cl=90%; ltpd= 10 %) mil - std - 202g:103b (2002) jeita ed - 4701:100 103 (2001) high temperature storage ta= 105 5 c test time= 1000hrs 22 pcs (cl=90%; ltpd= 10 %) mil - std - 750d:1031 (1995) mil - std - 883g:1008 (2006) jeita ed - 4701:200 201 (2001) low temperature storage ta= - 55 5 c test time= 1000hrs 22 pcs (cl=90%; ltpd= 10 %) jeita ed - 4701:200 202 (2001) environmental test temperature cycling 100 c 25 c - 40 c 25 c 30mins 5mins 30mins 5mins 3 0 cycles 22 pcs (cl=90%; ltpd= 10 %) mil - std - 750d:1051 (1995) mil - std - 883g:1010 (2006) jeita ed - 4701:100 105 (2001) jesd22 - a104c (2005) thermal shock 100 5 c - 30 c 5 c 15mins 15mins 3 0 cycles (<20 secs transfer) 22 pcs (cl=90%; ltpd=10%) mil - std - 750d:1056 (1995) mil - std - 883g:1011 (2006) mil - std - 202g:107g (2002) jesd22 - a106b (2004) solder resistance t.sol = 260 5 c dwell time= 101 seconds 3mm from the base of the epoxy bulb 11 pcs (cl=90%; ltpd=18.9%) mil - std - 750d:2031(1995) jeita ed - 4701: 300 302 (2001) solderability t. sol = 245 5 c dwell time= 5 0.5 seconds (lead free solder, coverage R 95% of the dipped surface) 11 pcs (cl=90%; ltpd=18.9%) mil - std - 750d:2026 (1995) mil - std - 883g:2003 (2006) mil - std - 202g:208h (2002) ipc/eia j - std - 002 (2004) soldering iron t. sol = 350 5 c dwell time= 3.5 0.5 seconds 11 pcs (cl=90%; ltpd=18.9%) mil - std - 202g:208h (2002) jeita ed - 4701:300 302 (2001) 1 0 . others the appearance and specifications of the product may be modified for improvement, without prior notice.
|
